Address: Naberezhnaya Severnoy Dviny, 17, Arkhangelsk, 163002, Russian Federation, Northern (Arctic) Federal University named after M.V.Lomonosov, office 1425

Phone: +7 (8182) 21-61-18
E-mail: forest@narfu.ru
http://lesnoizhurnal.ru/en/

Lesnoy Zhurnal

Production of High-Yield Hardwood Pulp by Bisulfite Minimizing the Chlorine Content Cooking

Версия для печати

T.A. Koroleva, L.A. Milovidova, A.A. Dryakhlitsyn

Complete text of the article:

Download article (pdf, 0.5MB )

UDС

676.16.022.32

Abstract

The article presents the results of the development of a technological mode for obtaining bisulfite hardwood pulp of high yield on a magnesium base for the production of various types of containerboard. The reliable and effective chemical and heat recovery technology implemented in the bisulfite method allows to use it in independent sulfite process. The effect of the duration of stay at the final temperature on the pulp yield and kappa number was studied when developing the technological mode of cooking. It was found that the increase in the duration of stay at the final temperature of 160 °C more than 40 min leads to violations of the selectivity of the cooking process. Increasing the duration of stay at the final temperature up to 70 min is accompanied by a decrease in pulp yield by 6 % at a constant value of the kappa number of the semi-finished product. Technological cooking mode: hydromodule 5, SO2 consumption 15.0 %, cooking solution pH 4.3–4.5, impregnation time at 120 °C – 35 min, cooking duration at 160 °C – 40 min. The mode allows to get a semi-finished product with a high yield of 60–65 % with a kappa number of 58–60 units without a hot grinding stage. An assessment of the mechanical strength characteristics of the laboratory samples of bisulfite pulp was carried out in accordance with the standards of the Russian Federation. The obtained values of bursting strength, resistance to flat compression, breaking strength, and breaking stress were comparable with the values of the industrial sample of hardwood neutral sulfite semi-chemical pulp with a semi-finished product yield of 75–78 %. It is shown hat the presence of bark in the technological chips in the amount of 7.5 % is accompanied by a decrease in the yield of bisulfite hardwood pulp by 4.5 % and mechanical strength by 7.8 %.

Authors

Tatiana A. Koroleva1,2, Candidate of Engineering, Assoc. Prof.; ResearcherID: ABB-5651-2020, ORCID: https://orcid.org/0000-0002-9477-5864
Lyubov A. Milovidova1, Candidate of Engineering, Leading Engineer of Research Planning and Support Department; ResearcherID: AAH-5551-2021, ORCID: https://orcid.org/0000-0001-8035-5300
Andrey A. Dryakhlitsyn1, Engineer of Research Planning and Support Department; ResearcherID: AAH-5772-2021, ORCID: https://orcid.org/0000-0001-8218-8569

Affiliation

1Northern (Arctic) Federal University named after M.V. Lomonosov, Naberezhnaya Severnoy Dviny, 17, Arkhangelsk, 163002, Russian Federation; е-mail: tataak@mail.rul.milovidova@narfu.ru
2N. Laverov Federal Center for Integrated Arctic Research, Naberezhnaya Severnoy Dviny, 23, Arkhangelsk, 163000, Russian Federation; е-mail: tataak@mail.ru

Keywords

hardwood, bisulfite pulp, technological process, pulp properties, neutral sulfite pulp, containerboard, fluting

For citation

Koroleva T.A., Milovidova L.A., Dryakhlitsyn A.A. Production of High-Yield Hardwood Pulp by Bisulfite Cooking. Lesnoy Zhurnal [Russian Forestry Journal], 2021, no. 3, pp. 161–169. DOI: 10.37482/0536-1036-2021-3-161-169

References

1. Bobrov A.I., Mutovina M.G., Bondareva T.A., Malyshkina V.K. Production of Fibrous Semi-Finished Products from Hardwood. Moscow, Lesnaya promyshlennost’ Publ., 1984. 245 p.
2. Galeyeva N.A. Semi-Chemical Pulp and High Yield Pulp Production. Moscow, Lesnaya promyshlennost’ Publ., 1970. 317 p.
3. State Standard. GOST 10070–74. Pulp and Semi-Pulp. Method for Determinating Kappa Number. Moscow, Izdatel’stvo standartov, 1999. 6 p.
4. State Standard. GOST 20682–75. Paper for Corrugation. Method for Determining the Resistance of Corrugated Paper to Flat Compression (Concoro Medium Test). Moscow, Izdatel’stvo standartov, 1989. 6 p.
5. State Standard. GOST 13525.1–79. Fibre Semimanufactures, Paper and Board. Tensile Strength and Elongation Tests. Moscow, Standartinform Publ., 2007. 5 p.
6. State Standard. GOST 15815–83. Technological Chips. Specifications. Moscow, Izdatel’stvo standartov, 1992. 14 p.
7. State Standard. GOST 13525.8–86. Fibre Intermediate Products, Paper and Board. Method for Determination of Resistance to Bursting. Moscow, Standartinform Publ., 2007. 6 p.
8. State Standard. GOST 10711 – 97. Paper and Board. Method for Determination of Breaking Force by Ring Compression (RCT). Moscow, Izdatel’stvo standartov, 2003. 6 p.
9. D’yakova E.V. Influence of Characteristics of Fibers and Their Relative Content in the Paper Pulp on the Deformation and Strength Properties of Containerboard: Cand. Eng. Sci. Diss. Abs. Arkhangelsk, 2004. 19 p.
10. Lavrov I.V. Improving the Technology of Paper for Corrugation Based on the Composition of Primary and Secondary Fibers: Cand. Eng. Sci. Diss. Abs. Arkhangelsk, 2012. 20 p.
11. Nepinin N.N. Technology of Pulp: in 3 Vol. Ed. by N.N. Nepinin. Vol. 1: Production of Sulfite Pulp. Moscow, Lesnaya promyshlennost’ Publ., 1976. 624 p.
12. Nepenin Yu.N., Zhalina V.A., Kuryatnikov A.B. Comparative Evaluation of Different Methods of Hardwood Semichemical Pulp Production. Lesnoy Zhurnal [Russian Forestry Journal], 1987, no. 1, pp. 75–78. URL: http://lesnoizhurnal.ru/apxiv/1987/№1-1987.pdf
13. Nepinin Yu.N., Zhalina V.A., Kenin V.G., Kuryatnikov A.B. Modern Methods of Semichemical Pulp Production. Moscow, VNIPIEIlesprom Publ., 1985. 36 p.
14. Annergren G., Germgård U. Sulfite Pulping: Process Aspects for Sulfite Pulping. Appita, 2014, no. 67, pp. 270–276.
15. Atalla R.H., Ranua J., Malcolm E. Raman Spectroscopic Studies of the Structure of Cellulose: A Comparison of Kraft and Sulfite Pulps. Tappi Journal, 1984, vol. 67, no. 2, pp. 96–99.
16. Dorland R.M., Leask R.A., Mckinney J.W. Pulp Production with Sodium Bisulfite: The Cooking of Spruce. Pulp and Paper Journal, 1958, no. 10, pp. 236–237.
17. FAOSTAT. Materials of the Official Site of the Food and Agriculture Organization of the United Nations. Available at: http://www.fao.org/faostat/en/#home (accessed 03.03.20).
18. Lundberg U. The European Containerboard Market. Paper 360°, 2020. Available at: https://paper360.tappi.org/2018/09/25/the-european-containerboard-market/ (accessed 03.03.20).
19. Santos R.B., Hart P.W. Effect of Eucalyptus Bark Contamination during Pulping of Mixed Southern Hardwoods. Tappi Journal, 2016, vol. 15, no. 11, pp. 707–715. DOI: https://doi.org/10.32964/TJ15.11.707
20. Tripathi S.K., Alam I., Bhardwaj N.K. Effect of Bark Content in Mixed Hardwood Chips on Pulp and Papermaking Properties. Nordic Pulp & Paper Research, 2020, vol. 35, iss. 3, pp. 235–331. DOI: https://doi.org/10.1515/npprj-2020-0017
21. Yorston F.N. Studies on Sulfite Pulping. Dominion Forest Service Bulletin, 1942, no. 97, pp. 20–29.




Production of High-Yield Hardwood Pulp by Bisulfite Minimizing the Chlorine Content Cooking

 

Make a Submission


ADP_cert_2024.png

Lesnoy Zhurnal (Russian Forestry Journal) was awarded the "Seal of Recognition for Active Data Provider of the Year 2024"

INDEXED IN: 


DOAJ_logo-colour.png

logotype.png

Логотип.png